Replacement dishwasher spray arm
Use it for: This is the new part you are installing in place of the damaged or worn arm.
Shop dishwasher spray armsDishwasher repair
How to Replace a Dishwasher Spray Arm
To replace a dishwasher spray arm, remove the rack if needed, release the old arm and retaining cap, clean the mounting hub, install a matching arm, spin it by hand, and run a short test wash. If you want an easy-to-clean version, confirm it is made for your model and water-feed style.
A clogged, cracked, warped, or loose spray arm can leave dishes dirty even when the dishwasher sounds normal. The trick is matching the exact arm and hub. A cleanable replacement is useful only if it fits correctly and still clears the racks and dishes.
Before you start: Match the spray arm by dishwasher model, upper or lower position, hub style, retaining cap, and whether the replacement is cleanable or sealed.
Safety first
- Do not force plastic clips, caps, or spray arm mounts. They can crack easily and turn a simple repair into a larger one.
- Keep screws, clips, and rack stops together so nothing falls into the sump area.
- If you pause a cycle to inspect arm movement, be careful of hot water and steam inside the tub.
Tools you may need
Phillips screwdriver
Use it for: Some dishwashers use a screw or rack stop that needs to come off for access.
Get a Phillips screwdriver
Needle nose pliers
Use it for: Helpful for small clips, caps, or retaining tabs without forcing them.
Get needle-nose pliers
Soft brush or old toothbrush
Use it for: Use it to clean the mounting area and clear debris before installing the new arm.
Get a cleaning brush
Towel or sponge
Use it for: Catches drips and wipes away debris from the sump area or rack.
Get shop towelsAs an Amazon Associate I earn from qualifying purchases. Repair Riot may earn a commission at no extra cost to you.
Step-by-step fix
Step 1: Make sure the spray arm is really the problem
- Open the dishwasher and inspect the spray arm you plan to replace.
- Look for cracks, melted spots, split seams, clogged spray holes, or an arm that sags or wobbles on its mount.
- Spin the arm by hand. It should turn smoothly without scraping the rack, dishes, or tub.
- If the arm is badly clogged, try rinsing and clearing the holes first so you do not replace a part that only needed cleaning.
- Compare the old arm to the new one before you start. The length, mounting style, and connection point should match.
If it works: You have confirmed the spray arm is damaged, worn out, or loose, and the replacement part appears to match.
If it doesn’t: If the arm looks fine and spins normally, the cleaning problem may be coming from low water flow, a blocked filter, or another wash system issue instead.
Stop if:
- The new spray arm does not match the old one.
- The spray arm mount, feed tube, or rack connection is cracked or broken.
- You find melted plastic or signs of electrical overheating inside the tub.
Step 2: Set up the dishwasher for safe, easy access
- Turn off the dishwasher at the control panel so it cannot start while you are working.
- Open the door fully and remove the lower rack if you are replacing the lower spray arm.
- If you are replacing a middle or upper spray arm, slide out the upper rack and remove any rack stop or end cap only if needed for access.
- Place a towel under the work area to catch drips and keep small clips or caps from rolling away.
If it works: You can reach the spray arm and its mounting point clearly without forcing the rack or door.
If it doesn’t: If the rack will not move far enough for access, look for a simple rack stop, end cap, or retaining tab that can be removed and reinstalled.
Stop if:
- A rack stop, rail, or spray arm support is cracked and will not hold the rack safely.
- You cannot access the spray arm without disassembling parts beyond the arm mount and rack hardware.
Step 3: Remove the old spray arm
- Check how the old spray arm is held in place. It may lift off, twist off, unclip, or use a small retaining cap or screw.
- Support the spray arm with one hand and remove the retainer with the other so you do not bend the mount.
- Pull the old spray arm straight off once the retainer is free.
- Set the retainer aside if the new part does not include one.
- Inspect the removed arm for cracks, worn center bushings, or heavy buildup that explains the failure.
If it works: The old spray arm is off and the mounting hardware is accounted for.
If it doesn’t: If the arm will not release, stop pulling harder and recheck for a hidden clip, quarter-turn lock, or center fastener.
Stop if:
- The mounting stem or feed tube starts twisting, cracking, or separating from the dishwasher.
- A seized fastener will not loosen and feels likely to strip or break.
Step 4: Clean and inspect the mounting area
- Wipe the mount, feed opening, and nearby surfaces with a towel or sponge.
- Use a soft brush to remove food debris, mineral buildup, or grease from the spray arm seat and water outlet.
- Check that the water feed opening is clear and that the mounting point is not worn oval, split, or loose.
- If the old spray arm dropped plastic pieces or debris, remove them before installing the new part.
If it works: The mounting area is clean, clear, and ready for the new spray arm.
If it doesn’t: If buildup is still blocking the water outlet, keep cleaning until the opening is clear enough for water to pass freely.
Stop if:
- The spray arm mount is cracked, loose, or too worn to hold the new arm securely.
- You find broken plastic deeper in the wash system that you cannot safely remove from the opening.
Step 5: Install the new spray arm
- Position the new spray arm exactly like the old one so the water inlet and mounting point line up.
- Press, twist, clip, or screw it into place using the same attachment method the old arm used.
- Reinstall any retaining cap, clip, or screw snugly, but do not overtighten plastic parts.
- Spin the new spray arm by hand several times. It should turn freely and sit level without rubbing.
- Reinstall the rack stop or end cap if you removed one, then slide the rack back into place.
If it works: The new spray arm is secured properly and spins freely by hand.
If it doesn’t: If the arm binds, remove it and check for a crooked fit, wrong part, misplaced retainer, or debris under the hub.
Stop if:
- The new spray arm will not lock onto the mount even though you are using the correct attachment method.
- The arm rubs because the mount or rack alignment is damaged.
Step 6: Run a short wash and confirm the repair held
- Run the dishwasher on a short cycle or rinse cycle with the racks in place and no oversized items blocking the arm.
- Listen for smooth operation instead of scraping, rattling, or repeated knocking.
- After a few minutes, pause the cycle carefully and check whether the spray arm has changed position, which suggests it is spinning during the wash.
- At the end of the cycle, confirm dishes are getting wet in the normal coverage area and that the spray arm is still attached firmly.
If it works: The dishwasher runs normally, the spray arm stays secure, and wash coverage has improved.
If it doesn’t: If cleaning is still poor or the arm is not moving, check for low water flow, a blocked filter, a feed tube problem, or an incorrect replacement part.
Stop if:
- The new spray arm comes loose during the cycle.
- You hear grinding, strong burning smells, or leaking that was not present before the repair.
Replacement Parts
Find a dishwasher spray arm on Amazon
Match the spray arm by dishwasher model, upper or lower position, hub style, retaining cap, and whether the replacement is cleanable or sealed.
As an Amazon Associate I earn from qualifying purchases. Repair Riot may earn a commission at no extra cost to you.
Verify the repair
- The new spray arm matches the old one in size and mounting style.
- The spray arm spins freely by hand without hitting the rack, dishes, or tub.
- Any retaining cap, clip, or screw is back in place and snug.
- A short wash cycle runs without scraping, rattling, or the arm coming loose.
- Wash coverage is improved and the arm remains secure after the cycle.
FAQ
Can I clean a dishwasher spray arm instead of replacing it?
Yes. If the arm is only clogged, remove it if possible and rinse out the spray holes. Replace it when it is cracked, warped, loose at the hub, or no longer stays attached securely.
How do I know if I need the upper or lower spray arm?
Open the dishwasher and inspect which arm is damaged or not spinning properly. Lower arms sit at the bottom of the tub, while upper or middle arms are attached under a rack or near the top wash area.
Why is my new spray arm not spinning?
The most common causes are the wrong replacement part, debris under the hub, a blocked water feed opening, or dishes blocking the arm. A damaged mount can also keep the arm from sitting correctly.
Do I need to shut off water or power to replace a spray arm?
For a basic spray arm swap inside the tub, you usually only need to turn the dishwasher off at the controls so it does not start while you are working. If your repair turns into deeper disassembly, stop and reassess before going further.
What if the spray arm keeps falling off?
That usually points to a worn retainer, damaged hub, or broken mounting stem. Replacing only the arm may not solve it if the mount itself is cracked or loose.
Can I replace my dishwasher spray arm with an easy-to-clean version?
Yes, if that version is listed for your dishwasher model and uses the same hub, feed tube, and retainer. Do not choose by diameter alone.