Replacement HRV / ERV filter
Use it for: This is the new filter going into the unit.
Shop HRV / ERV filtersHRV / ERV filter replacement
How to Replace an HRV / ERV Filter
To replace an HRV / ERV filter, turn the unit off, open the access panel, remove the old filter, install the new one in the same orientation, close the panel, and confirm airflow and operation return to normal.
A clogged or collapsed filter can choke airflow, make the unit work harder, and reduce fresh-air exchange. This is usually a straightforward homeowner job as long as you match the replacement correctly and reinstall it in the right direction.
Before you start: Match the filter size, thickness, airflow direction, and HRV / ERV model compatibility before ordering.
Safety first
- Turn the HRV / ERV off before opening the access panel.
- Wear gloves because cabinet edges can be sharp.
- Do not install a filter that is wet, damaged, or the wrong size.
Tools you may need
Screwdriver
Use it for: Some access panels use screws or quarter-turn fasteners.
Find a screwdriver set
Vacuum with brush attachment
Use it for: Helps remove dust from the filter compartment before installing the new filter.
Shop vacuums with brush attachment
Work gloves
Use it for: Protects your hands from sharp sheet-metal edges inside the cabinet.
Find work glovesAs an Amazon Associate I earn from qualifying purchases. Repair Riot may earn a commission at no extra cost to you.
Step-by-step fix
Step 1: Make sure the filter is the likely problem
- Check for signs of restricted airflow such as weak fresh-air movement, more dust around vents, a dirty filter reminder, or a visibly clogged filter.
- Locate your HRV / ERV access panel and confirm the filter is user-accessible without disassembling the whole unit.
- If you already have the replacement, compare its size and thickness to the old filter before opening the cabinet.
If it works: You have a strong reason to replace the filter and a replacement that appears to match.
If it doesn’t: If the unit has no accessible filter, or the replacement does not match the old one, pause and verify the correct part before going further.
Stop if:
- The cabinet shows water damage, burnt wiring, melted plastic, or heavy corrosion.
- The filter area is not accessible without removing internal components beyond a normal service panel.
Step 2: Shut the unit off and open the access panel
- Turn the HRV / ERV off at its wall control or service switch.
- If the unit is plugged into a nearby outlet and the plug is easy to reach, unplug it for extra safety.
- Put on gloves, then open or remove the access panel carefully so you do not bend it or drop screws.
Step 3: Remove the old filter and check its orientation
- Slide the old filter out slowly so built-up dust does not spill into the cabinet.
- Look for an airflow arrow or note which side faced into the unit so the new filter goes in the same way.
- Check the old filter for heavy dust loading, collapse, moisture, or damage that could explain poor airflow.
Step 4: Clean the filter compartment
- Use a vacuum with a brush attachment to remove loose dust from the filter slot, rails, and nearby surfaces.
- Wipe away any remaining dry dust with a soft cloth if needed.
- Keep debris out of the blower area and do not spray cleaner into the unit.
Step 5: Install the new HRV / ERV filter
- Insert the new filter in the same direction as the old one, following any airflow arrow on the frame.
- Slide it fully into place so it sits flat and does not buckle or leave gaps around the edges.
- Reinstall and secure the access panel so it closes evenly.
If it doesn’t: If the filter feels too tight, too loose, or will not sit flat, remove it and recheck size, thickness, and orientation before running the unit.
Step 6: Restore power and confirm the repair holds
- Plug the unit back in if you unplugged it, then turn it on at the control.
- Listen for normal startup and check that airflow at supply and exhaust grilles feels steadier than before.
- If your unit has a filter timer or maintenance reminder, reset it using the normal control settings for your system.
- Check again after 10 to 15 minutes to make sure the unit keeps running normally without unusual noise or panel vibration.
If it works: The HRV / ERV runs normally, airflow is restored, and the new filter stays in place during operation.
If it doesn’t: If airflow is still weak or the unit still struggles, the problem may be elsewhere, such as a blocked core, dirty fan, stuck damper, or control issue.
Stop if:
- The unit will not restart, trips power, makes grinding or scraping noises, or shows signs of overheating.
Replacement Parts
Find an HRV / ERV filter on Amazon
Match the filter size, thickness, airflow direction, and HRV / ERV model compatibility before ordering.
As an Amazon Associate I earn from qualifying purchases. Repair Riot may earn a commission at no extra cost to you.
Verify the repair
- The new filter matches the old one in size and thickness and is installed in the correct direction.
- The access panel closes fully without forcing it.
- Airflow at the vents feels normal or improved after startup.
- The unit runs for at least 10 to 15 minutes without unusual noise, vibration, or shutdown.
FAQ
How often should I replace an HRV / ERV filter?
It depends on the filter type, how much the system runs, and how dusty your home is. Many homeowners check the filter every few months and replace it when it looks loaded with dust or airflow starts to drop.
Can I clean the old filter instead of replacing it?
Only if your filter is a washable style. Many HRV / ERV filters are meant to be replaced, not washed. If the filter media is damaged, collapsed, or heavily loaded, replacement is the better choice.
What happens if I install the filter backward?
A backward filter can reduce airflow and may not trap dust the way it should. If the filter has an airflow arrow, point it the same way the old filter was installed or toward the unit's airflow direction.
Why is my HRV / ERV still not working well after a new filter?
A dirty filter is common, but not the only cause. If performance does not improve, the unit may have a dirty core, blocked intake or exhaust, fan problem, damper issue, or control fault.
Do all HRV / ERV units use the same filter?
No. Filter size, thickness, frame style, and compatibility vary by unit. Always match the replacement to your existing filter and your HRV / ERV model before ordering.